08B0-1X1T-06-F is a Bel Fuse MagJack Ethernet connector that combines a single RJ45 port with integrated magnetic components for 10/100BASE-T Ethernet connectivity. The part uses a right angle through hole mounting configuration and includes integrated green and orange yellow LEDs for network status indication.
The complete 08B0-1X1T-06-F configuration is designed around a 1X1 port arrangement, 10/100BASE-T Ethernet, upward-facing tab orientation and non-PoE operation. These characteristics make it a practical interface component for Ethernet equipment where the RJ45 connector and Ethernet magnetics need to be integrated into one PCB-mounted assembly.
08B0-1X1T-06-F belongs to the MagJack ICM family and integrates the physical Ethernet connector interface with the magnetic interface required by the network circuit.
The device provides one RJ45 port and supports 10/100BASE-T Ethernet with AutoMDIX capability. It uses a 90 degree right angle configuration so the connector interface extends horizontally from the PCB rather than vertically.
This arrangement is particularly useful for networking equipment where the RJ45 port needs to be accessible from the side or rear of an enclosure.
The part is designed for through hole PCB mounting and uses solder termination, providing mechanical retention as well as electrical connection to the board.
The main function of 08B0-1X1T-06-F is to provide a physical interface for 10/100BASE-T Ethernet.
Unlike a simple RJ45 receptacle, this MagJack configuration incorporates Ethernet magnetics into the connector assembly.
This integration can reduce the number of separate components required around the Ethernet interface and can simplify the PCB area dedicated to the network port.
The 10/100BASE-T specification makes the component suitable for Ethernet systems operating at traditional 10 Mbps and 100 Mbps data rates.
The connector uses a standard RJ45 interface with a single Ethernet port.
The single-port configuration is useful for embedded Ethernet equipment that needs one network connection rather than a multi-port connector assembly.
The RJ45 interface is commonly used for wired Ethernet connections in industrial controllers, networking equipment, embedded computers and other electronic systems.
The connector has an upward tab direction, which is an important mechanical characteristic when designing the enclosure and mating interface.
The integrated magnetic interface is one of the most important characteristics of 08B0-1X1T-06-F.
Ethernet magnetics provide electrical isolation and help interface the physical Ethernet transceiver with the network cable.
By integrating the magnetic components into the RJ45 assembly, the designer can avoid implementing the connector and magnetic interface as completely separate mechanical components.
This can simplify the Ethernet section of the PCB and make the port easier to integrate into a compact equipment design.
08B0-1X1T-06-F uses a 1X1 port configuration.
This means the component provides one Ethernet connector port in one horizontal position rather than a stacked or multi-port arrangement.
For single Ethernet interface products, this provides a straightforward PCB solution.
The 1X1 structure also gives the designer more flexibility when positioning a single network connection along the edge of a PCB.
The component uses through hole PCB mounting.
Through hole mounting is particularly useful for connectors because the mechanical forces generated when an Ethernet cable is inserted or removed are transferred to the PCB through the mounting terminals.
For equipment with frequent cable connection and disconnection, mechanical retention is an important part of connector selection.
The PCB layout should provide the required mounting holes and solder land configuration for the specific 08B0-1X1T-06-F footprint.
08B0-1X1T-06-F uses a 90 degree right angle orientation.
The right angle configuration allows the RJ45 cable to connect from the side of the PCB.
This is particularly useful when the PCB is installed inside a rectangular enclosure and the Ethernet connector needs to align with an external panel opening.
The mechanical position of the connector should therefore be considered together with the enclosure design.
The connector includes integrated green and orange yellow LED indicators.
Integrated LEDs allow network status information to be displayed directly beside the Ethernet port.
This can help users identify link or activity conditions without adding separate indicator components elsewhere on the front panel.
For equipment designers, the integrated LED configuration can also simplify the mechanical design because the indicators remain physically associated with the RJ45 connector.
08B0-1X1T-06-F uses a shielded construction with EMI fingers.
Ethernet interfaces are exposed to signals and cable environments that can make electromagnetic compatibility an important consideration.
The connector shield provides a conductive structure around the interface, while the EMI contact arrangement helps establish the intended connection between the connector and the surrounding shielding structure.
The final EMI performance depends on the complete PCB grounding and enclosure design rather than the connector alone.
The component is specified for 10/100BASE-T and AutoMDIX applications.
AutoMDIX allows the Ethernet interface to automatically accommodate different transmit and receive pair arrangements, reducing the need to distinguish between certain cable wiring configurations.
This is useful in embedded Ethernet equipment where the network interface needs to work with standard Ethernet connections without requiring manual cable-type selection.
The actual AutoMDIX function is implemented by the Ethernet PHY and associated circuitry, while the 08B0-1X1T-06-F provides the physical magnetic connector interface.
08B0-1X1T-06-F is specified as a non PoE MagJack configuration.
This distinction is important when selecting an Ethernet connector for a PoE-enabled product.
A non-PoE connector should not be assumed to provide the necessary magnetic and electrical characteristics for Power over Ethernet applications.
If the equipment needs to deliver or receive power through the Ethernet cable, a specifically qualified PoE magnetic solution should be evaluated instead.
The specified operating temperature range is 0°C to +70°C.
This range is suitable for many indoor electronic systems and standard commercial equipment environments.
For equipment installed in industrial locations, designers should evaluate the actual temperature around the connector rather than relying only on ambient room temperature.
If the application requires operation below 0°C or above +70°C, another compatible MagJack configuration with a wider temperature range may be more appropriate.
The connector has an approximate height above the PCB of 13.49 mm.
This dimension is particularly important for enclosure and PCB mechanical design.
The height of the RJ45 port determines where the external panel opening needs to be positioned relative to the PCB.
When replacing an existing Ethernet connector, even a relatively small difference in board height can affect the alignment between the connector and enclosure.
The connector uses copper alloy contacts with a gold finish.
The contact structure is designed for reliable electrical connection between the mating RJ45 plug and the PCB-mounted connector assembly.
For production equipment, the mating connector, insertion cycle requirements and mechanical environment should all be considered when evaluating long-term connector reliability.
The connector should also be mounted according to the recommended PCB design to maintain the intended mechanical alignment.
08B0-1X1T-06-F can be used in electronic equipment requiring a single 10/100BASE-T Ethernet connection.
Potential applications include embedded controllers, industrial control equipment, communication devices, networking hardware and other PCB-based products with a wired Ethernet interface.
Its integrated magnetic interface and LED indicators make it especially useful when the Ethernet port needs to be implemented as a compact board-level module.
For industrial electronic equipment using a standard 10/100BASE-T Ethernet interface, the through hole construction can be useful because the connector is mechanically secured to the PCB.
The integrated magnetics also simplify the physical Ethernet interface.
However, the 0°C to +70°C temperature range should be checked carefully before using the component in industrial environments with wider temperature requirements.
The connector's environmental specifications should always be matched to the actual installation conditions.
PCB design around 08B0-1X1T-06-F should account for both the electrical Ethernet interface and the mechanical structure of the RJ45 connector.
The through hole mounting points need to be correctly positioned.
The connector opening should align with the enclosure.
The shield connection should be integrated into the overall EMI strategy.
The LED pins need to be connected according to the intended indication circuit.
The Ethernet signal routing should also be designed with appropriate attention to the requirements of the connected PHY and magnetic interface.
When looking for an 08B0-1X1T-06-F replacement, matching the RJ45 interface alone is not sufficient.
The replacement should be checked for the complete configuration, including 1X1 port arrangement, 10/100BASE-T operation, integrated magnetics, right angle orientation, through hole mounting, LED configuration, tab direction and non-PoE design.
The physical dimensions are equally important.
A connector with similar electrical functionality but a different board height or mounting position may not fit an existing enclosure or PCB.
For an existing design, the original footprint and mechanical drawing should therefore be compared before approving a replacement.
An alternative to 08B0-1X1T-06-F should reproduce the functions required by the original Ethernet interface.
If the application requires a single 10/100BASE-T port, the alternative needs to support that network interface.
If the PCB depends on a right angle through hole connector, a vertical or surface mount alternative is not mechanically equivalent.
If integrated LEDs are part of the product interface, the alternative should provide a compatible LED arrangement.
For this reason, selecting an 08B0-1X1T-06-F alternative requires both electrical and mechanical comparison.
Buyers searching for 08B0-1X1T-06-F suppliers should use the complete part number rather than searching only for RJ45 MagJack.
The full MPN identifies the specific Bel Fuse configuration, including its port arrangement, Ethernet speed, mounting style and LED configuration.
ElecSuppliers provides an electronic component supplier platform where buyers can search for suppliers associated with specific part numbers.
For an 08B0-1X1T-06-F sourcing request, buyers can provide the required quantity, application and purchasing requirements when contacting suppliers.
Before purchasing 08B0-1X1T-06-F, buyers should confirm the complete part number and ensure that the connector configuration matches the PCB design.
The most important points include the 1X1 port configuration, 10/100BASE-T capability, right angle orientation, upward tab direction, integrated LED arrangement, through hole mounting and non-PoE configuration.
For replacement projects, the board height and mechanical mounting dimensions should be checked before placing a production order.
For larger quantities, packaging, availability, lead time and supplier capability should also be confirmed.
The complete 08B0-1X1T-06-F designation should be retained in the BOM and supplier documentation.
This is particularly important because the Bel Fuse MagJack family contains visually similar Ethernet connector configurations.
Small differences in the part number can correspond to changes in LED configuration, Ethernet function, temperature range, mounting arrangement or other mechanical characteristics.
Searching and purchasing by the complete MPN helps reduce the risk of selecting a connector that appears similar but is not mechanically or electrically compatible.
08B0-1X1T-06-F combines an RJ45 connector and Ethernet magnetic interface in a single PCB-mounted component.
Its key characteristics include a 1X1 port configuration, 10/100BASE-T operation, AutoMDIX application, right angle through hole mounting, integrated green and orange yellow LEDs, EMI shielding, upward tab orientation and non-PoE configuration.
This combination makes the part particularly suitable for single-port Ethernet equipment where the connector needs to provide both network access and an integrated magnetic interface.
08B0-1X1T-06-F is a Bel Fuse 1X1 MagJack Ethernet connector designed for 10/100BASE-T applications.
Its integrated magnetic interface, right angle through hole construction and built-in LED indicators make it more than a basic RJ45 receptacle. The specific configuration is intended for single-port Ethernet equipment where PCB mounting, enclosure alignment and integrated network interface components are important.
For engineers, the most important selection factors are the Ethernet configuration, integrated magnetics, port orientation, LED arrangement, mounting method and mechanical dimensions.
For buyers searching for 08B0-1X1T-06-F suppliers, ElecSuppliers provides a dedicated electronic component sourcing platform where the complete part number can be used to identify suppliers and submit purchasing requirements.
V1651A5 Short Hinge Roller Lever Snap Action Switch
JP026821UNL 10 100 Base TX RJ45 MagJack Connector
Explore related electronics articles and guides.
LM324PT is an STMicroelectronics quad operational amplifier in TSSOP-14 with 3V to 30V single supply operation for signal conditioning sensing and control circu...
JP026821UNL is a Pulse Electronics 1-port RJ45 MagJack for 10/100 Base-TX Ethernet with integrated magnetics LEDs and EMI shielding for embedded network equipme...
955347N001 is the TE Connectivity part number for 202K132-3-0-CS7025 heat shrink cable boot Explore its role in cable protection sealing and reliable wire termi...
LM324ADT is a quad low power operational amplifier from STMicroelectronics with a wide supply range and common mode input range Learn its circuit advantages and...
IRF640NSTRLPBF is a 200V N channel power MOSFET in a D2PAK package Learn its voltage current RDS on gate charge and practical power switching characteristics
SAMV71Q21RT-DHB-E is a Microchip SAM V71 32 bit microcontroller with an Arm Cortex M7 core Explore its memory peripherals package and RT grade characteristics
PTA6043-2010CIA203 is a Bourns 20K audio slide potentiometer with 60mm travel carbon element and PCB terminals Learn why its long travel suits audio control app...
V-165-1A5 is an Omron 16A basic switch with a short hinge roller lever and SPDT contacts Explore its mechanical characteristics terminal options ratings and rep...
D3V1651A5 is an Omron 16A miniature basic switch with a short hinge roller lever and SPDT contacts Learn what makes this version different and what to check whe...
MPC564MZP56 is a legacy NXP 32 bit PowerPC microcontroller in a BGA388 package Learn its architecture peripherals package details and what to check when sourcin...
IRF640NSTRLPBF is a 200V 18A N channel power MOSFET in D2PAK Learn its RDS on gate drive requirements switching characteristics and practical applications
SAMV71Q21RT-DHB-E is a 300 MHz radiation tolerant Arm Cortex-M7 MCU in a 144 pin ceramic CQFP package Learn why this version is used in aerospace and space elec...
Copyright © ElecSuppliers.com. All Rights Reserved.